• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Repairs to uPVC Windows

uPVC is a fantastic choice for modern homes. They are easy to maintain and durable, as well as long-lasting. They do not decay or rust as timber and aluminum.

Cleaning and lubricating regularly UPVC windows and doors is essential. This will prevent unnecessary repair costs and increase energy efficiency.

1. Broken Glass

If the glass in your window has been damaged, it could cause a large amount of damage to your home, making it very hazardous and possibly fatal. It is important to ensure that your windows are in good condition.

Single-pane windows are fairly simple to replace, and they typically fit into frames of the past easily. If you have double-paned windows which are joined by internal beading, it will be harder to remove and replace the old panes. In this instance, it is necessary to purchase plastic spacers to help the new pane fit into the window frame.

If you are going attempt to remove the window panes yourself it is crucial to wear appropriate safety gear, including thick gloves and protective eyewear. It is also recommended to lay down a dropcloth before you start working on the glass, so that any shards will fall onto the fabric instead of landing on the floor where they can be trampled upon and cause further damage.

Once the glass has been removed and the glass is removed, it's a good idea to cover the gap with clear packaging tape or duct tape to stop water and drafts from entering the property until a professional comes out and repair the window. It also acts as a barrier that will prevent any intruders from getting access to your home. If the gap between the door and the window is significant, you may prefer security screens that has windows. This will give you the best of both.

2. Sagging

Upvc windows and doors are a cost-effective energy efficient, durable and long-lasting alternative to timber windows with sash. However, with time, they may be afflicted by a variety of issues like sliding. A sagging window can cause problems with light, draughts or even security. It's crucial to act when you realize that your uPVC windows are sliding.

Repositioning the hinges can help fix a window that is sliding. First, you'll need to unblock the windows so you can access the frame. After that, using a screwdriver, you can unscrew the top and bottom hinges and adjust them by turning them clockwise or counter-clockwise. Close your window to test the fit after having relocated your hinges. If you're happy with the fit, tighten the screws until they remain in the right place.

If you cannot reposition the hinges, you could have to replace the seal. Over time rubber seals can lose their elasticity and become dry and cause them to loosen. It is crucial to replace your seal as quickly as you can to ensure that your uPVC window watertight and draughtproof.

uPVC handles can also loosen up. The majority of the time, this is caused by screws that have become loose over time. However, it could also happen because the handle mechanism has worn out. Fortunately, it's easy to fix the handle of a window that is loose yourself. You'll first need to close the window and then perform a test fitting. The joints at the corners of the sash should align with the joint on the casing. If it does not you can use a screwdriver to loosen up the handle. Then, turn the mechanism back into place.

3. Water Leaks

It is crucial to act if you wake up every morning to discover mouldy walls and wet floors. Water leaks from windows can not only cause degradation of your home's structure but also hinder your efforts to control the temperature in your home. Most often, uPVC window leaks are caused by a damaged or missing sealant.

This is a simple fix that can be done by any DIYer who is competent. Depending on the severity of the issue is, old caulking might need to be removed. It is essential to remember that when it comes to uPVC window repairs, you should avoid the temptation to "over-caulk in order to make the area harder to clean and reduce your energy efficiency.

Check that any drainage holes are free of debris inside them and that the sill pan is properly angled to drain away from the window. In more severe cases, you may need to replace the window.

Other signs of long-term water leakage are sills that are rotten and the appearance of black spots of mold on the wall near the window. This fungus thrives in conditions of dampness and can spread quickly throughout the house.

It is also important to remember that if the leakage originates from the glass of your double-glazed windows, it is more likely to be an issue with the glass seal rather than the frame or sagging. It is also possible to be corrected by a uPVC window expert who can replace the glass seal and regain the full insulation properties of your windows.

4. Faulty Hinges

If your uPVC windows are stiff to open, or loose and open with a breeze, it may be hinges that are at fault. They can be replaced by any competent DIYer and can be completed in just a few minutes.

Nearly every home in the UK will have top-hung or side hung uPVC windows that use hinges and, like all mechanical parts, they are susceptible to wear and tear over time. It's easy to change a window hinge, but it's simpler if you have someone to help hold the frame.

Make sure that the uPVC hinges open and close in the right direction. Look for the arrows that are on each hinge to determine which direction the window should be opened.

The problem can be caused by opening the window incorrectly or by a poor installation in the factory. This can often be resolved by sending us a photograph through our website and we will be pleased to offer you advice.

It is also essential to lubricate the hinges on a regular basis. Applying a light engineering lubricant on the hinges is a great method to accomplish this. We suggest using the lubricant that doesn't contain solvents, such as 3-in-1 Multi-Purpose oil. Regular lubrication can allow the window to open and close more easily. It also helps prevent corrosion and reduce the risk of sticking. Ideally, you should do this at least once a year. WD40 and other solvent based oils are not recommended because they will damage parts of your uPVC window.

5. Draughts

Draughts in Upvc windows can be caused by a few various factors. The hinges may also become misaligned due to wear, which can cause an opening where the sash and frame meet. This can be easily repaired by giving them a thorough clean, however when they're beyond repair, it could be necessary to have them realigned or replaced. The second is the interlock, which is on the hinge side of the window, may also be misaligned, and again it's possible to just give them a good clean, but in certain cases, it may be necessary to have them replaced.

The next common reason for draughts are the window seals, these are prone to wear or damaged over time, and let air escape through the gaps. This can be avoided by replacing them with high-quality weatherstripping. Another option is to replace the upvc window with low-emissivity glass. this will help to regulate indoor temperatures and again will reduce the possibility of draughts.

Another method of reducing the amount of draughts is to use a Draught-excluder. These are usually made of fabric tubes filled with a filler, which can be put on top of your window sill. They can keep your home warm by blocking out cold air.

The windows made of upvc can continue to provide excellent insulation and security for your home with a little regular maintenance and repairs. It is important to remember that all windows eventually wear out and it is more cost-effective to simply replace them than to repair them. If you have any problems with your upvc window repair window, it's best to consult a professional as soon as possible.